A Range Rover Evoque engine rebuild can bring a tired or damaged engine back to near-new condition. But what actually happens during a rebuild, and which parts are replaced? Knowing this helps you compare quotes, check the quality of the work and understand where your money goes. A proper rebuild replaces every key wear part, not just the one that failed. At Engine Solutions in Grays, UK, we rebuild Evoque engines every week. In this guide, we explain which parts are usually replaced, plus engine codes, specifications and engine replacement costs in the UK.
Parts Replaced in the Bottom End
The bottom end is the lower part of the engine. It includes the crankshaft, con rods, pistons and oil system. During an Evoque engine rebuild, the engine is stripped and every part is cleaned, measured and checked. These parts are usually replaced:
- Main bearings and big-end bearings: These wear over time, especially when the oil is old or diluted. They’re always replaced.
- Thrust washers: These control the crankshaft’s end float.
- Piston rings: New rings restore compression and reduce oil use.
- Pistons: These are replaced if they’re scored, cracked or damaged.
- Con rod bolts: These are stretch bolts, so they must be replaced, not reused.
- Oil pump: This is replaced or rebuilt to restore full oil pressure.
- Crankshaft oil seals: New front and rear seals stop leaks.
The crankshaft itself is usually reground or polished rather than replaced. However, if it’s cracked or badly scored, a new crankshaft is fitt. In addition, the cylinder bores are hone or re-bored so the new rings seal properly.
Parts Replaced in the Top End and Timing System
The top end includes the cylinder head, valves and camshafts. The timing system keeps everything moving in sync. These parts are usually replace:
Cylinder head parts:
- Head gasket: This is always replace.
- Cylinder head bolts: These are stretch bolts, so they’re always renewe.
- Valve stem seals: New seals stop oil burning.
- Valves and valve seats: These are re-cut or replaced if worn or burnt.
- Hydraulic lifters and cam followers: These are replace if they’re noisy or worn.
Timing parts:
- Timing chain or timing belt kit: On the 2.0 Ingenium, the timing chain, guides and tensioners are always replace. On the 2.2 diesel, a new timing belt, tensioner and idlers are fitt.
Other parts:
- Water pump and thermostat
- Injector seals and washers
- Glow plugs on diesel engines
- Turbo oil feed and return lines, or an oil feed filter
- All gaskets, O-rings and seals
The cylinder head is also pressure-teste for cracks and skimm flat. As a result, the rebuilt engine seals properly and runs smoothly.
Range Rover Evoque Engine Codes and Model Table
Different Evoque engines need slightly different rebuild parts. Here are the engines use in the Evoque and the main focus of each rebuild.
| Engine | Generation | Years | Engine Code | Size | Power | Main Rebuild Focus |
| eD4 / TD4 / SD4 | L538 | 2011–2015 | 224DT | 2.2 L I4 diesel | 150–190 PS | Timing belt, bearings, injectors |
| Si4 (Ford EcoBoost) | L538 | 2011–2017 | 204PT | 2.0 L I4 petrol | 240 PS | Pistons, timing chain, turbo lines |
| eD4 / TD4 Ingenium | L538 | 2015–2018 | 204DTD | 2.0 L I4 diesel | 150–180 PS | Timing chain kit, bearings |
| Si4 Ingenium | L538 | 2017–2018 | PT204 | 2.0 L I4 petrol | 240–290 PS | Timing chain, coolant parts |
| D150 / D180 / D240 | L551 | 2019–2020 | 204DTD / 204DTA | 2.0 L I4 diesel | 150–240 PS | Timing chain kit, bearings |
| D165 / D200 MHEV | L551 | 2020–present | 204DTD (MHEV) | 2.0 L I4 diesel | 163–204 PS | Timing chain, bearings, seals |
| P200 / P250 / P300 | L551 | 2019–present | PT204 | 2.0 L I4 petrol | 200–300 PS | Timing chain, valve stem seals |
| P160 / P300e | L551 | 2020–present | PT153 | 1.5 L I3 petrol | 160–309 PS | Timing chain, cooling parts |
You can find your engine code on your V5C or the engine block. Alternatively, send us your VIN, and our Range Rover Engine Works team will confirm it before quoting.
Range Rover Evoque Engine Specifications
Here are the key specifications for the two most common Evoque diesel engines.
2.2 Diesel (224DT)
- Layout: Inline four-cylinder, DOHC, 16 valves
- Displacement: 2,179 cc
- Bore x stroke: 85.0 mm x 96.0 mm
- Compression ratio: 15.8:1
- Fuel system: Common-rail injection
- Induction: Variable-geometry turbo (twin turbos on the SD4)
- Camshaft drive: Timing belt
- Block: Cast iron
2.0 Ingenium Diesel (204DTD)
- Layout: Inline four-cylinder, DOHC, 16 valves
- Displacement: 1,999 cc
- Bore x stroke: 83.0 mm x 92.4 mm
- Compression ratio: 15.5:1
- Fuel system: 2,000-bar common-rail injection
- Induction: Variable-geometry turbocharger
- Camshaft drive: Timing chain at the rear of the engine
- Block: Aluminium with iron liners
These specifications affect which parts are replace. On the 224DT, the cast-iron block is tough, so rebuilds focus on bearings, the timing belt and injectors. On the 204DTD, the timing chain sits at the back of the engine. Because the engine is already out during a rebuild, it’s the perfect time to fit a full new chain kit.
Why Choose Our Engines?
If your engine is too badly damage to rebuild, a reconditioned JLR engine is the next best option. When comparing reconditioned engines vs used engines, the parts list makes all the difference.
A used engine is sell as it is. Nothing has been replace, and its history is often unknown. As a result, it may already have worn bearings, a stretched chain or leaking seals.
Our reconditioned engines, on the other hand, get the same full parts list as a rebuild. That includes new bearings, piston rings, timing parts, head gasket, seals and gaskets. We also machine the crankshaft and cylinder head where needed. Finally, every engine is pressure-test and check before it leaves our workshop.
Here’s why Evoque owners choose our engines:
- Every key wear part is replace, not just the failed one.
- Known Evoque weak points are fix on every rebuild.
- Every engine comes with a warranty.
- Engines are match to your exact VIN and engine code.
- We keep a wide range of Range Rover engines for sale in stock.

UK’s No.1 Engine Reconditioners
Engine Solutions specialises only in Jaguar and Land Rover engines. Because of this focus, our team knows exactly which parts each Range Rover Evoque engine needs during a rebuild.
Our supply and fit services cover both rebuilds and replacements. For a rebuild, we remove your engine, replace all the key parts in-house and refit it. For an engine replacement, we supply a reconditioned unit and fit it at our workshop. In both cases, we use fresh oil, filters, coolant and new gaskets. After that, we code the engine, update the software and road-test your Evoque before handover.
Most importantly, we offer No Upfront Charges and No Deposit Required. You only pay once the job is complete and you’re fully satisfy. This takes the stress out of a major repair.
We also provide a full parts list with every job, so you know exactly what’s been replace. If you’re ready to buy a reconditioned Range Rover Evoque engine or book a rebuild, contact our team today for a free, no-obligation quote.
Real Engine Work, Real Specialist Support
At our Range Rover garage in Grays, every rebuild follows a clear process. First, our Range Rover Engine Works team strips the engine and cleans every part. Next, we measure the bores, crankshaft and cylinder head against factory specifications. Then we replace all key wear parts, machine surfaces where needed and rebuild the engine with the correct torque settings.
Here’s a guide to engine rebuild and engine replacement costs in the UK:
| Engine | Rebuild (Your Engine) | Reconditioned (Fitted) |
| 2.2 Diesel (224DT) | £2,500 – £4,000 | £2,800 – £4,500 |
| 2.0 Ingenium Diesel (204DTD) | £3,000 – £5,000 | £3,500 – £5,500 |
| 2.0 Petrol (204PT / PT204) | £3,000 – £5,000 | £3,500 – £5,500 |
These prices are a guide only. The final cost depends on whether extra parts are need, such as a new crankshaft, pistons or a turbo.
We always give you a fixed, itemised quote and photos of worn parts. In short, you get real engine work and real specialist support.
Nationwide Vehicle Recovery
Engine Solutions is based in Grays, Essex, but we serve Evoque owners across the whole UK. Our logistics service makes rebuilds and replacements easy, wherever you are.
If your Evoque can’t be driven, we can arrange nationwide vehicle recovery to our workshop from England, Scotland and Wales. Once the work is complete, we can return the vehicle to your home or business. Alternatively, if you prefer to use your local garage, we can deliver a reconditioned engine directly to them.
Every engine is secure to a pallet, seal against dirt and moisture, and ship with a trust courier. In addition, you get tracking updates from dispatch to delivery, so you always know when it will arrive.
Our Grays location is close to the M25, A13 and Port of Tilbury. As a result, we can deliver quickly to London, Essex, Kent and the rest of the country. Next-day delivery is also available on most stock engines. Simply put, you can shop with us online or by phone, and we’ll handle the rest.
Frequently Asked Questions
1. Which parts are always replace during an Evoque engine rebuild?
Bearings, piston rings, the head gasket, head bolts, seals, gaskets and the timing chain or belt kit are always replace. Other parts are replace if they’re worn.
2. Is the crankshaft replace during a rebuild?
Not always. The crankshaft is usually reground or polished, but it’s replace if it’s cracked or badly damaged.
3. How much does an Evoque engine rebuild cost in the UK?
An Evoque rebuild usually costs £2,500 to £5,000, depending on the engine and parts needed. A reconditioned engine fitted costs around £2,800 to £5,500.
4. Do I need to pay a deposit?
No. We offer No Upfront Charges and No Deposit Required, and you only pay once the job is complete.
5. Can you collect my Evoque if it won’t start?
Yes. We offer nationwide vehicle recovery to our Grays workshop and can return your vehicle once the job is finish.
